Audio Volume Booster

Boost a quiet voice memo, tame a recording that is too loud, or normalise a track so it reaches full volume without distortion. The tool shows your file’s loudest point so you know how much room there is.

  • Files stay on your device
  • Free, no sign-up
  • Instant
Drop an audio file here MP3, WAV, M4A, OGG, FLAC or WebM

Processed on your device. Your files are not uploaded to any server.

Quick guide · 4 steps

How to use the Volume Booster

When to use the Volume Booster

Quiet phone recordings

Lectures and meetings recorded from the back of a room are often too quiet to hear on headphones.

Matching clips in a project

Bring several clips to a similar level before joining them so the listener does not have to adjust the volume.

Background music under speech

Lower music by 10–15 dB so it sits behind a voice-over instead of competing with it.

Preparing audio for sharing

Normalise a podcast or song so it plays at a healthy level on phones and laptops.

Features and benefits

  • Change volume from −20 dB to +20 dB in half-decibel steps
  • One-click normalize to −1 dBFS
  • Peak meter in dBFS before you start
  • Distortion protection that caps the boost automatically

Example

Input
lecture.m4a – loudest point −14.2 dBFS
Output
Normalize → +13.2 dB → lecture-volume.mp3, peak −1.0 dBFS

How the Volume Booster works

ConvertNest scans every sample to find the peak level and shows it in dBFS (decibels relative to full scale). A change of X decibels multiplies every sample by 10^(X/20). With distortion protection on, the multiplier is reduced if it would push the peak above full scale, so no sample is clipped. Normalize calculates the exact multiplier that puts the peak at −1 dBFS, leaving headroom for MP3 encoding.

A real-life example

A teacher records a lesson on her phone from the front desk, but the file peaks at only −18 dBFS and students complain it is hard to hear. She chooses Normalize: the tool raises everything by 17 dB so the loudest moment sits at −1 dBFS. The lesson now plays at a normal level on students’ phones, and because nothing was pushed past full scale, there is no crackle.

Good to know

Decibels measure volume changes on a scale that matches how we hear: +6 dB roughly doubles the signal level and sounds clearly louder, while +3 dB is a small but noticeable step. Digital audio cannot go above 0 dBFS (full scale); anything pushed past it is clipped, which sounds like crackling.

Normalize finds the single loudest sample and raises everything by the same amount until that peak sits at −1 dBFS, leaving a little headroom for MP3 encoding. It is the safest way to make a recording as loud as possible without changing its sound.

If the loudest point is already near 0 dBFS but the recording still sounds quiet, a short peak such as a door slam is limiting the boost. Cut that part out first with the Audio Cutter, then normalise again.

Tips for the best results

  1. Try Normalize first – it gives the biggest safe boost in one click.
  2. For a large boost on a recording with one loud spike, cut the spike out first.
  3. Use −6 dB to roughly halve the level of music that will sit under speech.
  4. Listen on headphones after boosting; quiet background noise becomes more obvious.

Common mistakes to avoid

Turning off distortion protection to force +20 dB

Clipped audio crackles and cannot be repaired later. Keep protection on unless you know you need it.

Boosting a recording that is already at 0 dBFS

There is no headroom. Lower the loud peaks first or accept the current level.

Expecting a boost to remove noise

Changing the volume affects everything equally. Hiss and hum get louder with the voice.

Volume Booster – frequently asked questions

How much louder can I make a file?

Up to +20 dB. With distortion protection on, the boost stops automatically at the point where the loudest sample would clip.

What does normalize do?

It raises (or lowers) the whole file by one fixed amount so its loudest point reaches −1 dBFS. The balance between quiet and loud parts stays the same.

Will boosting add noise?

Background hiss gets louder by the same amount as the voice, because the tool changes the overall level. It does not add new noise.

Can I make a file quieter?

Yes. Move the slider below zero, for example −6 dB to roughly halve the level.

What does dBFS mean?

Decibels relative to full scale: 0 dBFS is the loudest a digital file can be, and every lower level is a negative number.

Is this the same as loudness normalisation for Spotify?

Not exactly. Streaming services measure average loudness (LUFS). This tool normalises the peak, which is simpler and never causes clipping.